728x90
반응형
10.7 Security
10.7.1 Display Content Integrity Checker (DCIC)
10.7.1.1 Test Name
- mxc_dcic_test.out
10.7.1.1.1 Location
/unit_tests/DCIC/
10.7.1.1.2 Functionality
DCIC의 목표는 디스플레이로 전송된 안전에 중요한 정보가 손상되지 않았는지 확인하는 것이다.
10.7.1.1.3 Configuration
None
10.7.1.1.4 Use Case and Expected Output
# ./mxc_dcic_test.out -bw 18 -dev 1mxc_dcic_test.out에 대한 예상 출력:
Opened fb0
open /dev/dcic1
bpp=16, bus_width=18
Config ROI=1
Config ROI=3
Config ROI=5
ROI=0,crcRS=0x0, crcCS=0x0
ROI=1,crcRS=0x6cd6b18d, crcCS=0x6cd6b18d
ROI=2,crcRS=0x0, crcCS=0x0
ROI=3,crcRS=0xc9da7ae6, crcCS=0xc9da7ae6
ROI=4,crcRS=0x0, crcCS=0x0
ROI=5,crcRS=0xb5ba1453, crcCS=0xb5ba1453
ROI=6,crcRS=0x0, crcCS=0x0
ROI=7,crcRS=0x0, crcCS=0x0
ROI=8,crcRS=0x0, crcCS=0x0
ROI=9,crcRS=0x0, crcCS=0x0
ROI=10,crcRS=0x0, crcCS=0x0
ROI=11,crcRS=0x0, crcCS=0x0
ROI=12,crcRS=0x0, crcCS=0x0
ROI=13,crcRS=0x0, crcCS=0x0
ROI=14,crcRS=0x0, crcCS=0x0
ROI=15,crcRS=0x0, crcCS=0x0
All ROI CRC check success!
10.7.2 SIM
10.7.2.1 Test Name
- mxc_sim_test.out
10.7.2.1.1 Location
/unit_tests/SIM/
10.7.2.1.2 Functionality
SIM 카드 인터페이스의 기본 테스트.
10.7.2.1.3 Configuration
None
10.7.2.1.4 Use Case and Expected Output
/unit_tests/mxc_sim_test.out
Expected output
atr[0]= 0x3b atr[1]= 0x68 atr[2]= 0x0 atr[3]= 0x0 atr[4]= 0x0 atr[5]= 0x73 atr[6]=
0xc8
atr[7]= 0x40 atr[8]= 0x0 atr[9]= 0x0 atr[10]= 0x90 atr[11]= 0x0
rx[0] = 0x6e rx[1] = 0x0
rx[0] = 0x6d rx[1] = 0x0
rx[0] = 0x6e rx[1] = 0x0
10.7.3 SNVS Real Time Clock (SRTC)
10.7.3.1 Test Name
- autorun-rtc.sh
- rtctest.out
- rtcwakeup.out
10.7.3.1.1 Location
/unit_tests/SRTC/
10.7.3.1.2 Functionality
이 테스트는 시간과 날짜를 유지하는 데 사용되는 RTC(Real Time Clock) 모듈을 검사한다. 사용자에게 인증 가능한 시간을 제공하고 카운터 변조가 감지되면 알람을 발생시킬 수 있다.
10.7.3.1.3 Configuration
autorun-rtc.sh, rtctest.out와 rtcwakeup.out를 작동하려면, 대상 보드 defconfig 파일에 다음 라인을 추가한다:
CONFIG_RTC_DRV_SNVS=y
10.7.3.1.4 Use Case and Expected Output
./autorun-rtc.sh
or
./rtctest.out $lt;arg>
--full run all tests
--no-periodic don't run periodic interrupt tests
or
./rtcwakeup.out -d rtc0 -m mem -s 10
Expected output
autorun-rtc.sh: Exit with PASS results.
rtctest.out: The program ends with "Test complete" status.
rtcwakeup.out: System is wakeup after 10s.i.MX 7D Sabre SD의 예상 출력
- autorun-rtc.sh
-
autorun-rtc.sh i.MX7D Checking for devnode: /dev/rtc0 autorun-rtc.sh: PASS devnode found: /dev/rtc0 Running test case: ./rtctest.out --no-periodic RTC Driver Test Example. Counting 5 update (1/sec) interrupts from reading /dev/rtc0: 1 2 3 4 5 Again, from using select(2) on /dev/rtc0: 1 2 3 4 5 Current RTC date/time is 21-2-2017, 23:13:07. Alarm time now set to 23:13:12. Waiting 5 seconds for alarm... okay. Alarm rang. *** Test complete *** Typing "cat /proc/interrupts" will show 1 more events on IRQ rtc. autorun-rtc.sh: PASS test case: ./rtctest.out --no-periodic rtc irqs before running unit test: 303 rtc irqs after running unit test: 314 so rtc irqs during test was: 11 checking rtc interrupts PASS autorun-rtc.sh: Exiting PASS - rtctest.out --full
-
./rtctest.out --full RTC Driver Test Example. Counting 5 update (1/sec) interrupts from reading /dev/rtc0: 1 2 3 4 5 Again, from using select(2) on /dev/rtc0: 1 2 3 4 5 Current RTC date/time is 21-2-2017, 23:14:48. Alarm time now set to 23:14:53. Waiting 5 seconds for alarm... okay. Alarm rang. Periodic IRQ rate was 1Hz. Counting 20 interrupts at: 2Hz: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 4Hz: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 8Hz: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 16Hz: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 32Hz: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 64Hz: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 *** Test complete *** Typing "cat /proc/interrupts" will show 131 more events on IRQ rtc. - rtctest.out --no-periodic
-
/rtctest.out --no-periodic RTC Driver Test Example. Counting 5 update (1/sec) interrupts from reading /dev/rtc0: 1 2 3 4 5 Again, from using select(2) on /dev/rtc0: 1 2 3 4 5 Current RTC date/time is 21-2-2017, 23:16:24. Alarm time now set to 23:16:29. Waiting 5 seconds for alarm... okay. Alarm rang. *** Test complete *** Typing "cat /proc/interrupts" will show 1 more events on IRQ rtc. - rtcwakeup.out -d rtc0 -m mem -s 10
-
./rtcwakeup.out -d rtc0 -m mem -s 10 rtcwakeup.out: wakeup from "mem" using rtc0 at Wed Feb 22 23:17:29 2017 PM: Syncing filesystems ... done. Freezing user space processes ... (elapsed 0.001 seconds) done. Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. Suspending console(s) (use no_console_suspend to debug) PM: suspend of devices complete after 639.100 msecs PM: suspend devices took 0.640 seconds PM: late suspend of devices complete after 1.236 msecs PM: noirq suspend of devices complete after 1.202 msecs Disabling non-boot CPUs ... CPU1: shutdown Turn off Mega/Fast mix in DSM Enabling non-boot CPUs ... CPU1 is up PM: noirq resume of devices complete after 0.756 msecs imx-sdma 30bd0000.sdma: loaded firmware 4.2 PM: early resume of devices complete after 0.972 msecs PM: resume of devices complete after 483.302 msecs PM: resume devices took 0.480 seconds Restarting tasks ... done.
728x90
반응형
'NXP i.MX SoC Family > i.MX Linux Reference Manual' 카테고리의 다른 글
| i.MX Linux Reference Manual (IMXLXRM) - Introduction - Overview (0) | 2022.10.24 |
|---|---|
| i.MX Linux Reference Manual (IMXLXRM) (0) | 2022.10.21 |
| i.MX Linux Reference Manual - Unit Tests - Audio (0) | 2022.09.02 |
| i.MX Linux Reference Manual - Unit Tests - Video (0) | 2022.09.01 |
| i.MX Linux Reference Manual - Unit Tests - Graphics (0) | 2022.09.01 |
